Openeye OE2-E120 Quick Start User Manual download pdf (Page 2)

DIRECTIONAL AND PLAYBACK CONTROL BUTTONS

Live

Go to PTZ mode.

PTZ

Adjust zoom, focus, and iris on a PTZ channel.

Start reverse playback of recordings. When pressed successively, the

search jumps back in time by 30 minute increments.

Search-Pause

When pressed successively, the reverse playback rate

decreases from 1/2X speed to 1/8X.

Live

Start playback of the latest recordings.

(By default, the system searches recordings in the past 30 secs. If no

recording is archived, the system will play back the latest one.)

PTZ

Adjust zoom, focus, and iris on a PTZ channel.

Start playback of recordings. When pressed successively, the search

jumps forward in time by 30 minute increments.

Search-Pause

When pressed successively, the playback rate increases from 1/2X

speed to 1/8X.

Navigation

Move up.

PTZ

Move the camera view point up.

Start Panorama Search.

Navigation

Move to the right.

PTZ

Move the camera view point to the right.

Play recorded videos.

Search-Pause

Step forward one frame.

Navigation

Move to the left.

PTZ

Move camera’s view point to the left.

Play recorded videos in reverse.

Search-Pause

Step back one frame.

Navigation

Move down.

PTZ

Move the camera view point down.

Start Smart Search.

Operation Modes: Live Mode, Live Freeze Mode, Search Mode, Search-Pause Mode,

Navigation Mode, and PTZ Mode.

FUNCTION BUTTONS

Live

Freeze live channels.

Live Freeze

Resume live view.

Pause playback channels.

Search Pause

Resume playback.

Rotate

Rotate through to the remaining channels in the current display mode or

rotate the display conﬁguration.

Preset

In PTZ mode, press to use the Preset function.

Setup

Open the setup menu.

Live

Change the display mode. Display switches in the following order when

the LIVE key is pressed successively: (Single > 4 > 7 > 9 > 10 > 13 > 16

> Single > 4 > 7 > 9 ...split screen mode)

Open the search menu.

Focus

In PTZ mode, press to use the Focus function.

Use the buttons to adjust.

Backup

In live mode, press to open the backup menu.

In the search mode,

Press once, to set the start time for Backup.

Press twice, to set the end time for Backup.

Press three times, to complete Backup.

•

Zoom

In PTZ mode, press to use PTZ Zoom function.

Use the buttons to adjust.

Key

Log out the current user. Use to prevent accidental or unauthorized sys-

tem-wide changes.

Iris

In PTZ mode, press to use the IRIS function.

Use the buttons to adjust.

Connect cameras to video inputs, and if using, connect PTZ camera control lines to RS485

connector.

Connect the main monitor to the VGA monitor output or main video output - BNC.

Connect analog monitors to looping video outputs. (optional)

Connect the monitor to SPOT video outputs (up to 3 on 16CH only). (optional)

Connect sensors to alarm signal inputs. (optional)

Connect alarm devices such as buzzers to alarm signal outputs. (optional)

Connect external controllers to RS232 connector. (optional)

Connect a speaker and microphone to the audio inputs and output. (optional)

Connect a network cable to the network port.

Power on all the connected equipment.

Connect the power cord to the DVR.

Turn the power switch on.

10.

11.

12.

QUICK INSTALLATION

When more than one E-Series DVR is installed in the same location, use one remote controller

to control multiple DVRs. To control multiple DVRs, you must change the remote controller ID to

match the SYSTEM ID of the DVR.

Follow the instructions below to change the remote controller ID.

On the DVR

Press SETUP on the front of the DVR or the Remote Controller.

Go to SYSTEM > SYSTEM SETUP.

Enter the desired SYSTEM ID number.

On the Remote Controller

Press and hold the ID button on the remote controller and enter the desired SYSTEM ID

number to operate the corresponding DVR.

Note The SYSTEM ID must be input as two numbers on the remote controller. Therefore you

should input 00 for the DVR ID 0 and input 01 for 1.

HOW TO USE IR REMOTE CONTROLLER

1 2

Comments to this Manuals

No comments

Openeye OE2-E120 Quick Start User Manual Page 2

Comments to this Manuals

Related products and manuals for Video Openeye OE2-E120 Quick Start